Beka Rigid Heddle Childs Loom 10"

This product is not a toy. It is built solidly and can be used to create real textiles, just limited in width.Exactly the same loom is sold as small loom (rather than a toy) in this listing Beka Rigid Heddle Loom Rigid Heddle Loom but at a higher cost.

I recently became interested in weaving and purchased this loom to see if I would enjoy weaving.I have completed several projects on this loom and I really do enjoy it.I was able to create several scarves and sashes which are 4 feet long.

Here are some things that I learned about the loom and the process.

I am attaching several photos which I will be referencing in this review.

1. This loom does not limit you too much in the length of the textile you produce, just the width. I made 4 feet long scarves and could have made them a few feet longer if I wanted.The threads that will be used in the textile are wrapped around the board at the top of the loom (called warp beam) and the finished textile tangles from the front of the loom.This loom does not have a cloth beam on which the fabric can wrapped. As you make fabric you upwrap the threads from the warp beam and pull it down between the boards at the bottom tightening the hand screws to put the threads in tension for weaving.You can see this illustrated in the photos I am attaching to this review.

2. This loom does not come with a few items that you will need for weaving. I read a few books and watched a few videos to understand what tools are needed and made most of them myself.

(1) You will need a warping board. This is a tool that allows you to measure out threads to put on the loom. I created one by purchasing a 1 foot board and 1/2 inch dowel from a local home improvement store. I asked the clerk to cut 1/2 inch dowel in two 9 inch pegs. I drilled two 1/2 inch holes in the board and put dowels into it gluing them for extra security. My dowels are 4 inches apart. If I were to do it again, I would put them 5 inches apart. I put a piece of felt on the bottom of the board. I also bought two C clamps to attach the board with pegs to my work table to create one end of a steady warp board. The leftover length of the 1/2 dowel is the second end of the warp board. I tie it to the chair and this allows me to place the second end as far as I need from the pegs on the board to measure out the length of the threads I need for the project. So for example, if I am planning to make a 4 foot scarf, I would put the dowel attached to the chair 5 feet away from the 9 inch pegs to give myself a foot for thread salvage. You can buy a warping board for about $120 dollar at a loom store. My solution cost under $10 dollars.

(2) You will also need a pick-up stick, which will allow you to pick up threads if you want to make a design.I got a stick which is used for mixing paints, and used sanding paper to create a pointy end.This took only a few minutes and made a tool which otherwise would cost a lot more.See photo of the tools I created.

(3) If you want to change colors in your design you will need another stick shuttle (the loom comes with one).Having more than one shuttle allows you to keep weaving without having to unwind the thread from the shuttle that comes with this loom which is time consuming and cat get your threads tangled.You can make your shuttle stick from the paint mixing stick by making notches at both end of the stick and then using sand paper to smooth out the notches.

What I like about this loom:

1. It let me try weaving without payinglot of money for a big loom

2. It is built solidly and works well

3. It is easy to use, it did not take me long to figure out how to weave

4. I liked that the loom came threaded, so it allowed you to start with weaving rather than "dressing" the loom (which is more tedious and complex than the weaving).

What I did not like about this loom:

1. The instructions that come with the loom are not sufficient to get you started if you are a novice

I had to read several books and videos to get me started.This not a big deal, just letting you know

that you would need extra information to avoid being frustrated

2. The screws that create tension at the bottom of the loom tend to catch threads

3. When the piece is long and it tangles from the front of the loom you need to be careful not to step on it or run it over with you chair

Overall, I am very pleased with the loom and my new hobby!

Updated 9/6/11

Since I started to weave the most helpful book for mastering weaving has been by Deborah Chandler Learning to Weave

Update 11/20/11

Dressing the loom can be challenging, if you don't keep all the threads straight it may take much longer then necessary.The most important thing is to come up with a way to hold your heddle while you are dressing the loom.I am attaching a photo of the system of clamps I came up with. I speeded up the dressing of the loom tremendously with a few simple clamps and brackets I found in a local home improvement store.I wish I came up with this system earlier I hope sharing this idea will save you time and frustration.

A paint mix stick is attached to the loom by a small clamp.This gives clearance on both sides of the heddle so you can approach it from both sides for dressing.The paint stick is attached to a metal bracket with another small clamp. And the metal bracket is attached to the table with a big clamp.The whole system takes about 1 minute to set up, and saves at least 30 minutes of fussing with threads.

Ali Julia review

I have never used a loom before and this seems a perfect starter piece. I already finished the "starter" project and am happy with the capabilities of my loom.

My biggest issue with the product is that the instructions are not detailed enough for a true beginner, trying to teach themselves. I don't mind using other resources for guidance, however the product says it comes with full instructions and I was a bit confused by some parts.

regardless, the product itself is lovely and just what I expected.

Buy Beka Rigid Heddle Childs Loom 10" Now

This is a great starter loom.I got it for myself to see if I would like weaving, and for my daughter to use when she got older.I now have moved on to a larger loom but will continue to use this for smaller projects.Very simple in design and usage, it would be a good for children ages three to seven with supervision but anyone over the age of eight could easily weave on it.

I like that it is entirely made of wood and is made in the USA.

Read Best Reviews of Beka Rigid Heddle Childs Loom 10" Here

I found this easy and fun to you use I have made several scarfs!I really enjoy this loom and I mean it is a real loom not a toy

Want Beka Rigid Heddle Childs Loom 10" Discount?

This loom is great for someone who wants to start out weaving, or just wants to weave on the side. The tension can get a little wonky sometimes, since tightening it requires flipping the block of wood, but its still a great piece. I upgraded to a 32 in Ashford loom, and still use this one for simple little scarves when I dont want to string up my big loom